| DOCUMENT NUMBER
|
PRODUCT
|
TITLE
|
DESCRIPTION
|
|
40
|
Legend Character Heights |
Available character heights other than .100 |
|
40
|
Non-glare faceplates |
For use in high-glare conditions |
|
40 & 90 |
Multiple Displays |
Multiple display types in one button |
|
40
|
High Contrast Legend Display |
Greater readability under low ambient light and bright sunlight conditions |
|
40
|
Bailing Circuit for Solenoid Held Switches |
Provides multi station switching or remote control capabilities |
|
40
|
Pushbutton Removal Lever Latch |
Special short latch lever |
|
40
|
Captive Pushbutton Option (40R) |
Pushbutton is held captive to switch/indicator |
|
40
|
Series 40R Pushbutton/display Screen Disassembly |
Disassembly Instructions for 40R pushbutton |
|
40
|
Model 40 and 40 RFI Shielded Switches |
Describes RFI Shielding in series 40 switches |
|
40
|
Installation/Removal Instructions for 40 Sw/Indicator Modules |
Describes installation and removal of modules from matrix housings |
|
40
|
Pushbutton Guard for Models 46 and 48 Switch |
Installation instructions of Pushbutton Guard P/N 15070 |
|
40
|
Panel Cut-Outs for Multiple Pushbutton Guards |
"Recommended Panel Cut-outs for part numbers 15007, 15055 and 15070" |
|
40 & 2S/2R |
Slot Mounting Individual Mount Switch/Indicators |
Formula for panel cut-outs for slot mounting switch/indicators |
|
40 |
Seismic Qualification Testing |
"Describes Seismic Qualification testing done on Series 40, 2S, and Series 60 switches" |
| |
|
|
|
|
50
|
Installation/Removal Instructions for Series 50 Pushbuttons |
Instructions on how to remove and reinsert series 50 pushbuttons |
|
"2, 40, 50, 80" |
Operating Force VS Travel |
Typical operating force versus pushbutton travel for momentary switches |
|
"49, 59, 89" |
Split Lamp Ground |
Terminal identification on split lamp ground configurations |
|
"2, 40, 50, 80" |
Installation /Removal Instructions |
"Instructions for removing pushbuttons for 4 lamp, square or rectangular pushbuttons" |
|
"2S, 40, 50, 80" |
Split Lamp Ground 4-Lamp Square Pushbutton |
Explains split lamp ground in relation to lamp positions and latch lever |
|
"2, 40, 50, 80" |
Operating Force VS Travel |
Typical operating force versus pushbutton travel for alternate action switches |
|
50
|
Pushbutton Guard P/N 15077 |
Describes Guard for use with 59 and 59C switches |
|
"40, 50, 80" |
MIL-STD-108D Definitions |
"Defines Disproof, Splash proof, Watertight and Submersible" |
|
"40, 50, 80, 90" |
Short Circuit Prevention |
Prevention of short circuit of lamp circuits |
| |
|
|
|
|
60 |
Series R60 RFI Pushbuttons |
Describes RFI capability for series 60 pushbuttons |
| |
|
|
|
|
"80, 90" |
Cleaning Instructions |
"Cleaning instructions for lighted pushbutton displays with an anti-reflective coating, Type 6 (SLR) and Type 7 (NVIS)" |
| |
|
|
|
|
90
|
Installation of Tie Retainer |
Instructions for installing tie retainer |
|
90 & 100 |
Legend Replacement Procedure |
Instructions for disassembly and installation of legend plate |
|
90
|
Installation and Removal Tools Crimp Pin |
"Instructions for installation or extraction of crimp pins, removal of pushbuttons, switches, and receptacle assemblies" |
|
90
|
Installation of Tie Retainer P/N 15093 |
Instructions for installing Tie Pushbutton retainer part number 15093 |
|
90
|
Installation of Tie Retainer P/N 15220 |
Instructions for installing Tie Pushbutton retainer part number 15220 |
|
90 |
Watertight Seal Lubrication |
Instructions to insure watertight joint between pushbutton seal and seal retainer collar when reinstalling switch assembly |
|
90 |
Installation Procedure for Crimp Contact Terminated Wiring Systems |
|
|
90 |
Pushbutton Contacts Cleaning |
Instructions for contact cleaning of LED lighted pushbuttons |
|
90 |
Soldering instructions for switch terminals |
Two categories of instructions. Category I address those terminals that are new and supplied by the manufacturer. Category II address those terminals that may have become contaminated |
|
"98, 99" |
Receptacle Assembly Installation Procedure |
Crimp pin receptacle installation instructions |
|
90 & 100 |
Switch removal instructions |
Instructions for user to remove pushbuttons from switch housing or matrix housing assembly |
|
90 & 100 |
Pushbutton Switch Assembly Installation |
Installation Procedure for S90 & S100 Series Pushbutton Switch Assemblies |
|
90 & 100 |
Crimp Pin Receptacle Assembly Installation |
Instructions for installation of crimp pin receptacle assembly for Series 100 and Series 90 crimp pin termination switches / indicators. |
| |
|
|
|
|
1M |
Mixed Tube Length for Matrix Housings |
"Accomodates solenoid held and latch down switch in assembly with momentary, alternate and indicator only." |
|
1M |
Installation Instructions Series 1M/1MR with Mounting Dress Bezel |
Describes installation of Matrix with Dress Bezel |
| |
|
|
|
|
5SM, 5M and 505M Series |
Product Enhancement for Dress Bezel Mounted Matrix |
Changes made to Assemblies intended for high impact shock applications to further enhance its strength. |
